Skip to content
Fitment · CFMOTO

UFORCE U10 Pro
wheels & tires.

Bolt pattern, studs and the 15-inch Packard wheel and tire sizes for the 2025–2026 CFMOTO UFORCE U10 Pro.

5x4.5 (5x114.3)Bolt pattern
M12x1.25Stud thread
2025–2026Model years covered

What fits

The numbers for your UFORCE U10 Pro.

Bolt pattern5x4.5 (5x114.3)

Polaris Pro R / Turbo R / Pro S / Xpedition / Ranger XD 1500 run M12x1.5 studs. CFMOTO Z10 / U10 Pro are 5x4.5 on M12x1.25 — same wheel, different lug nuts.

Stud threadM12x1.25

Lug nuts must match the pitch. The wrong one starts on the stud, then binds.

CentringLug-centric

Conical seats centre the wheel on the studs.

Factory wheels · tires14" · 29x9-14 front / 29x11-14 rear

Check it yourself

Measure before you order.

5x4.5 (5x114.3) · 5 studs on a 114.3 mm (4.5 in) circle
Five studs, none straight across.

Measure from the center of one stud to the outer edge of the stud two over. On this hub that reads about 114.3 mm (4.5 in).

Match the thread, not just the pattern.

M12x1.25 here. The wrong pitch starts on the stud and then binds.

Torque to the book.

Use the lug nut torque figure in your owner’s manual.

Taller tires cost acceleration.

Two inches over stock on a belt-driven car usually wants a clutch kit; sand paddles add rotating mass on top.

What Packard builds for it

6 forged styles in 5x4.5 (5x114.3).

15x7 fronts and 15x11 rears, forged centers with beadlock or standard-lip barrels. The machine decides the pattern; you decide the rest.

All 5x4.5 (5x114.3) wheels →Wheels filtered to your UFORCE U10 Pro →

Tires and parts

Finish the set.

Sand tires

Packard sand tires are built for 15-inch wheels. Steers up front, paddles in the rear.

All sand tires →

Same wheels fit

Machines that share 5x4.5 (5x114.3).

Same pattern, so the same Packard wheel. The stud thread can still differ, so check it on each page.

Questions

UFORCE U10 Pro fitment questions.

What bolt pattern does the CFMOTO UFORCE U10 Pro use?

The 2025–2026 CFMOTO UFORCE U10 Pro uses a 5x4.5 (5x114.3) bolt pattern. Polaris Pro R / Turbo R / Pro S / Xpedition / Ranger XD 1500 run M12x1.5 studs. CFMOTO Z10 / U10 Pro are 5x4.5 on M12x1.25 — same wheel, different lug nuts.

What lug nut thread does the CFMOTO UFORCE U10 Pro use?

M12x1.25 studs. Use lug nuts with that pitch. A nut with the wrong pitch starts on the stud and then binds.

Is the CFMOTO UFORCE U10 Pro hub-centric or lug-centric?

Lug-centric. Conical lug seats centre the wheel on the studs.

What size Packard wheels and tires fit the CFMOTO UFORCE U10 Pro?

Packard builds 15x7 fronts and 15x11 rears for it. Factory equipment is 14" · 29x9-14 front / 29x11-14 rear.

What other machines share wheels with the CFMOTO UFORCE U10 Pro?

The same 5x4.5 (5x114.3) pattern is on the Polaris RZR Pro R, Polaris RZR Turbo R, Polaris RZR Pro S, Polaris Xpedition, Polaris Ranger XD 1500, CFMOTO ZFORCE Z10, Segway Super Villain SX20. Check the stud thread before you swap lug nuts between them.